SMS Commands: Difference between revisions

Latest revision as of 10:56, 14 January 2026

Notes:

1234 – the System PIN code.
Engine start / stop and stand-alone engine pre-heater turn ON / turn OFF commands are available only if the appropriate function settings are ON.

Phonebook

SYNTAX			DESCRIPTION	SAMPLE
SN?	˽	NNNN	Add phonenumber NNNN to ? phonebook position (position number ? - 1 to 5)	1234 SN2 37068412345
SN0	˽	NNNN	Add phonenumber NNNN to first empty phonebook position	1234 SN0 37068412345
SR?			Clear ? Phonebook position (position number ? - 1 to 5)	1234 SR2
SI			Get SMS with all preprogramed numbers	1234 SI
SH1			Allow answer to any number and process SMS commands from any number	1234 SH1
SH0			Allow answer only to registered numbers and process SMS command only from registered numbers	1234 SH0

GPRS Settings

SYNTAX			DESCRIPTION	SAMPLE
SGA	˽	APN	Set APN (ask your network provider)	1234 SGA internet
SGU	˽	USER	Set user name (ask your network provider, leave blank if not required)	1234 SGU omni
SGP	˽	PASS	Set password (ask your network provider, leave blank if not required)	1234 SGP omni
APNAUTO			Set default APN, user name and password according to network code	1324 APNAUTO
REGISTER			Register your alarm system on alarmserver.net	1234 REGISTER
SGSE	˽	STATE	Turn on/off communication with Alarm server (STATE = 1 - on; STATE = 0 - off)	1234 SGSE 1
GPRS	:	STATE	Turn on/off communication with Alarm server (STATE = 1 - on; STATE = 0 - off)	1234 GPRS:1
SGSR	˽	ExTxSxGxFxCxZx	Alarm server setings. x=1 - enable; x=0 - disable. E - Report events (arm, disarm, alarm), Z - Report zones (open/close door, hood, trunk..), T - Report technical information (battery voltage, temperature, GSM signal level), S - Report system status (armed, disarmed, open zones etc), G - Report geolocation (GPS and GSM towers information) F - Forward data to 3rd party server C - Use custom address for reporting to Alarm server Note: it is not necessary to send all settings if you want to disable geolocation reporting only and leave other settings unchanged you can send: SGSRG0	1234 SGSR E1T0S1G0F1C0
SGSP	˽	PERIOD	Periodic report. PERIOD - value from 0 to 6. (0 - disabled; 1 - every 10min; 2 - every 30min; 3 - every 60min; 4 - every 6h; 5 - every 1d; 6 - every 2d)	1234 SGSP 2
SGSC	˽	CMS	CMS - corporate account number	1234 SGSC 12345
SGSA	˽	IP:PORT	IP address and port used for report forwarding to 3rd party server (SGSRF1) or it can be used as custom reporting address instead www.alarmserver.net (SGSRC1)	1234 SGSA 192.168.101.010:1010
SGTX			Enable/Disable GPS tracking (X=1 - enable; X=0 - disable)	1234 SGT1
GPS	:	STATE	Enable/Disable GPS tracking (STATE=1 - enable; STATE=0 - disable)	1234 GPS:0
ROAMING	:	STATE	Enable/Disable communication with server on roaming (STATE=1 - enable; STATE=0 - disable)	1234 ROAMING:1
REPORT			Enable full reporting to alarmserver.net (system will report events, zones, technical info, system status, geolocation, tracking and periodical reporting every 10min also will be enabled)	1234 REPORT
TCPCONTROL	:	STATE	Enable/Disable alarm system control over internet (STATE=1 - enable; STATE=0 - disable)	1234 TCPCONTROL:1
TRACKING	:	ACCUR	Change tracking accuracy, ACCUR – value from 1 to 5. (1 – very high, 2 – high, 3 – medium, 4 – low, 5 - very low) For Very high and high tracking accuracy VOUCHER code is required – check on alarmserver.net	1234 TRACKING:3
PINGPER	:	PERIOD	Setup short ping period, PERIOD – value from 0 to 5. (0 – disabled, 1 – 1min, 2 – 2min, 3 – 3min, 4 – 5min, 5 – 10min) Short ping is used to detect when alarm system is loosing connection with server. To enable short ping VOUCHER code is required – check on alarmserver.net	1234 PINGPER:0

Other Settings

SYNTAX					DESCRIPTION	SAMPLE
SERVICE	:	STATE			Enter/exit service mode (STATE = 1 - enter; STATE = 0 -exit)	1234 SERVICE:1
RESET	:	X			X=M - reset modem; X=F - full system reset	1234 RESET:M
UPGRADE					Upgrade device firmware (upgrade may take 5-10min, SMS will be send in case of success of failure)	1234 UPGRADE
PIN	:	PPPP			Change PIN. PPPP - new PIN code (4 digits, 1-9)	1234 PIN:1235
SL?					Set periodic SMS test interval, ? represents interval in days (1 to 4 days)	1234 SL4
ST	˽	temp			Adjust temperature sensor, temp - current temperature (+26, -8 etc.)	1234 ST +26
SU	˽	voltage			Set low battery warning voltage (type 119 for 11.9V, default 11.8V)	1234 SU 119
SF	˽	FN=SN			Set alarm system function FN seting number to SN (22=1)	1234 SF 22=1
SW	˽	time			Set engine preaheater operation time period in minutes	1234 SW 20
SM	˽	map			Select maps provider. Where map 0 or 1 (0 - maps.google.com; 1 - maps.yandex.ru)	1234 SM 1
LBSURL	:	url			Select location provider (by GSM data). Where url 0 or 1 (0 – opencellid.org, 1 – xinit.ru)	1234 LBSURL:0
F	˽	NNNN	˽	text	Forward text to NNNN	1234 F 37068412345 ELITA GN8
X1	˽	bal			Get SIM card balance, where bal is network provider specific command (245#, 100# etc.)	1234 X1 *254#
SMSREPCNT	˽	X			Set amount of SMS sending tries in case device failing to send SMS, because of network error (default: 3)

Messaging Settings

SYNTAX			DESCRIPTION	SAMPLE
	Default
	1-as	2 – 5-as
S?Mx			Mandatory call on alarm	1234 S1M1
S?Cx			Call on alarm	1234 S2C1
S?Vx			SMS on alarm	1234 S3V1
S?Ax			SMS on arm	1234 S1A1
S?Dx			SMS on disarm	1234 S1D1
S?Ex			SMS on remote engine start/stop or engine preaheater on/off	1234 S1E1
S?Tx			Trouble SMS	1234 S2T1
S?Px			Periodic test SMS	1234 S2P1
S?Fx			SMS forwarding	1234 S1F1
S?Qx			SMS command must be with PIN	1234 S1Q1
S?Xx			Control over SMS forbiden	1234 S1X0
S?Sx			SMS in smartphone format (Android only)	1234 S1S1
S?Kx			Arm/Disarm with short call (CLIP)	1234 S1K1
S?Ox			START/STOP engine remotely with short call (CLIP)	1234 S2O1
S?Wx			Turn ON/OFF engine preheater with short call (CLIP)	1234 S3W1
S?Ux			Turn ON/OFF push notifications	1234 S1U1

? - position number in phonebook (1 to 5)
x = 1 - Enabled
x = 0 - Disabled

Personal Messaging Settings

SYNTAX			DESCRIPTION	SAMPLE
	Default
	1-as	2 – 5-as
SMx			Mandatory call on alarm	1234 SM1
SCx			Call on alarm	1234 SC1
SVx			SMS on alarm	1234 SV1
SAx			SMS on arm	1234 SA1
SDx			SMS on disarm	1234 SD1
SEx			SMS on remote engine start/stop or engine preaheater on/off	1234 SE1
STx			Trouble SMS	1234 ST1
SPx			Periodic test SMS	1234 SP1
SFx			SMS forwarding	1234 SF1
SQx			SMS command must be with PIN	1234 SQ1
SXx			Control over SMS forbiden	1234 SX0
SSx			SMS in smartphone format (Android only)	1234 SS1
SKx			Arm/Disarm with short call (CLIP)	1234 SK1
SOx			START/STOP engine remotely with short call (CLIP)	1234 SO1
SWx			Turn ON/OFF engine preheater with short call (CLIP)	1234 SW1
SUx			Turn ON/OFF push notifications	1234 SU1

x = 1 - Enabled
x = 0 - Disabled

Control and status commands

SYNTAX			DESCRIPTION	SAMPLE
0 or I			Get system status	1234 I
A			Arm system	1234 A
D			Disarm system	1234 D
C			Clear alarm	1234 C
G			Start engine	1234 G
Q			Stop engine	1234 Q
61			Turn on optional control	1234 61
60			Turn off optional control	1234 60
99			Block the engine	1234 99
90			Unblock the engine	1234 90
X5			Get location SMS using GSM	1234 X5
X6			Get location SMS using GPS	1234 X6
PANIC	:	M	Panic mode. Direction indicators and/or siren go ON for 30s. M=L – with siren, M=S without siren	1234 PANIC:L
OPENTRUNK			Open cars trunk	1234 OPENTRUNK
ON	:	1 arba 2	Turn on system output configured as AUX1 or AUX2	1234 ON:1
OFF	:	1 arba 2	Turn off system output configured as AUX1 or AUX2	1234 OFF:1
V			Get SMS with system version	1234 V
BI			Get SMS with system BI number	1234 BI
USTS			Update system status to server	1234 USTS
GETOPEN			Get open zones by SMS	1234 GETOPEN
GETFN			Get all function settings (21=1 means FN21 SN1)	1234 GETFN
GETCAR			Get current vehicle group and subgroup	1234 GETCAR

CAN BUS Monitored Zones

SYNTAX					DESCRIPTION	SAMPLE
CANENABLE	:	zone			Enable zone monitoring over CAN-BUS	1234 canenable:ENGINE
CANDISABLE	:	zone			Disable zone monitoring over CAN-BUS	1234 CANdisable:HOOD
			zones:	hood	original hood sensor	1234 CANdisable:door
				door	original hood sensors
				trunk	original trunk sensor
				ignition	ignition status monitoring
				engine	running engine status monitoring
				omsensor	alarm from original sensor
				remote	arming/disarming from original remote or keyless access system

Engine Start Settings

SYNTAX			DESCRIPTION	SAMPLE
STARTTIME	:	TIME	Remote engine start duration in minutes (TIME from 5min to 45min)	1234 STARTTIME:15
STARTP	:	STATE	Enable/disable periodic engine start (STATE=1 - enable; STATE=0 - disable)	1234 STARP:1
STARTPERIOD	:	PERIOD	Periodic engine start period in hours (PERIOD from 2h to 24h)	1234 STARTPERIOD:3
STARTTIMEP	:	TIME	Periodic engine start duration in minutes (TIME from 5min to 45min)	1234 STARTPERIODP:15
STARTT	:	STATE	Enable/disable engine start by low engine temperature (STATE=1 - enable; STATE=0 - disable)	1234 STARTT:1
STARTTEMPERATURE	:	TEMP	Low engine temperature in °C (TEMP from 0°C to -25°C)	1234 STARTTEMPERATURE:-10
STARTTIMET	:	TIME	Low temperature engine start duration in minutes (TIME from 5min to 45min)	1234 STARTTIMET:15
STARTV	:	STATE	Enable/disable engine start by low battery voltage (STATE=1 - enable; STATE=0 - disable)	1234 STARTV:0
STARTVOLTAGE	:	VOLT	Low battery voltage in volts (VOLT from 10V to 12,5V)	1234 STARTVOLTAGE:11,8
STARTTIMEV	:	TIME	Low battery voltage engine start duration in minutes (TIME from 5min to 45min)	1234 STARTTIMEV:15
STARTC	:	STATE	Enable/disable engine start by calendar (STATE=1 - enable; STATE=0 - disable)	1234 STARTC:0
STARTCALENDAR	:	CAL	Engine start calendar (times for every weekday) CAL = 8:00,8:00,8:00,8:00,8:30,99:99,99:99 - Monday to Thursday engine start at 8:00, Friday - 8:30, Saturday and Sunday - no engine start	1234 startcalendar:8:00, 8:00, 8:00, 8:00 8:30, 99:99, 99:99
STARTTIMEC	:	TIME	Engine start by calendar duration in minutes (TIME from 5min to 45min)	1234 STARTTIMEC:10

NOTES

SMS message must be started with a valid 4-digit alarm system PIN code.
SMS commands are not case sensitive (1234 D and 1234 d are the same disarm command).
It is possible to add as many commands as you want, unless the total message length exceeds 160 symbols.
Commands F and X1 must be sent in separate SMS messages or added at the end of a command set (e.g., 1234 A F 37067012345 Hello, this is a forwarded SMS).

SMS command example: 1234 A — Arm system, 1234 is alarm system PIN

SMS command set example: 1234 SN1 37067012345 S1D1 — Add phone number 37067012345 to 1st phonebook position, enable SMS on disarm to 1st number, 1234 is alarm system PIN

NOTES for legacy devices with firmware version below v1.06

SMS message must be started with a valid 4-digit alarm system PIN code.
In front of every command * must be added. Also, * must be added instead of ˽ (space symbol) inside the command.
At the end of a command or command set (if multiple commands added) *# must be added.
SMS commands are not case sensitive (1234*D*# and 1234*d*# is the same disarm command).
It is possible to add as many commands as you want, unless the total message length exceeds 160 symbols.
Commands F and X1 must be sent in separate SMS messages or added at the end of a command set. In this case, do not add *# at the end (e.g., 1234*A*F*37067012345*Hello, this is a forwarded SMS).

SMS command example: 1234*A*# — Arm system, 1234 is alarm system PIN

SMS command set example: 1234*SN1*37067012345*S1D1*# — Add phone number 37067012345 to 1st phonebook position, enable SMS on disarm to 1st number, 1234 is alarm system PIN

@@ Line 3: / Line 3: @@
 # '''1234''' – the System PIN code.
 # Engine start / stop and stand-alone engine pre-heater turn ON / turn OFF commands are available only if the appropriate function settings are ON.
-# The System automatically ends the call if no button is pressed within 45 seconds.
 </div>